[. . . ] 29/29 3 1) Repose combiné (Mise correspondant) Handset, on hold position Passage de la vis antivol Concealed screw hole en attente d’un 2) 3) Touches Mémoires Urgence (Uniquement version avec 2 ou 3 mémoires) Memory keys (Models with 2 or 3 memory keys only) Clavier uniquement modèle HD2000 « Urgence à clavier »). 17 Introduction There are 4 different models of HD2 Urgence telephones: -HD2000 Urgence 1: with direct dialling of 1 programmed number when lifting the handset. - HD2000 Urgence 2: direct dialling of 2 programmed numbers when depressing key M1 or M2. [. . . ] NOTE: To erase a number stored in memory, proceed from 1 to 4, skip section 5 (Do not enter any digit) and terminate as in 6 and 7. NOTE: HD2000 Urgence 1 and Urgence à clavier factory settings come with “Urgence“ mode. In case of wrong operation, see « LIST OF SETTINGS » pages 24-25 and check that “Urgence” mode is selected. Setting access code : Setting choice 04 Urgency:1 20 Mode 2 HD2000 Urgence 2 or 3 1) Make sure HD2000 Urgence is connected to the line. 4) Dial the telephone number to store including *, # or "Pause" if needed (22 digits maxi). NOTE: In case of wrong operation, a long "beep" sound is emitted. NOTE: To erase a number stored in memory, proceed from 1 to 3, skip section 4 (Do not enter any digit) press the memory to erase as in 5 and terminate as in 6 and 7. NOTE: HD2000 Urgence2 and 3 factory settings come with “Normal“ mode. In case of wrong operation, see « LIST OF SETTINGS » pages 24-25 and check that “Normal” mode is selected. Setting access code : Setting choice 04 Normal:0 21 Settings programming Note: HD2000 Urgence standard factory settings come with: - Programming access code = 0000 - Dialling = Tone - Hook-Flash duration = 270 ms - Pulse mark-break ratio = 66/33 - Access to memory programming = unlocked - Call barring = unlocked To change settings, proceed as follows: 1) Make sure the telephone is connected to a powered C. 2) Depress « PGR » key located on the small keypad (Located at the back of the unit). 3) While keeping « PGR » key depressed, pick-up the handset. 6) Enter the 4 digits programming access code with the keypad (factory pre set code is: 0000) This code can be modified (see « LIST OF SETTINGS » section, pages 24-25). 7) If the right code is entered, 2 short « beep » tones will be heard and the access to settings, changes will be authorized. If a wrong code is entered, a low « beep » tone will be heard and the unit will return to talk mode. 8) Enter the 2 digits selected setting access code (see « LIST OF SETTINGS » section pages 24-25) 9) 2 sharp « beep » tones confirming the selection will be heard. 22 12) 2 sharp « beep » tones will confirm the storage of your new setting. Total Reset General reset operation erases memories, access code and will return all settings to factory settings (see « SETTINGS PROGRAMMING » section page 22). [. . . ] 4- If needed, install the third screw through the hole located above the telephone (See pages 28 and 29) and hide it with the foam plug. Boucle sèche (Option) Off-hook detection (Optional) Ligne/Line Ligne/Line Boucle sèche (Option) Off-hook detection (Optional) 26 Desk mount installation (Optional) see page 28 Use the optional desk-mount kit including one securing screw, a loaded desk mount base, 2 desk-mount black latches and the 4 non slip pads. 2- Pull of the 2 wall-mount black latches and replace them by 2 smaller desk-mount black latches. [. . . ]